Ampush logoAMPUSHWORKS
Home / Training / Syllabus

Programme 02 · One month · 102 hours

Embedded Systems and Microcontrollers

Embedded systems are the dedicated computers inside everyday products. This course teaches how microcontrollers are programmed in C and how they interact with switches, displays, sensors and communication modules, leading to the development of a small embedded product.

Duration1 month per programme
Course fee₹3,000 per candidate
Training hours102 hours: theory 32, practical 64, exams 6
Batch sizeMinimum 10 candidates per batch

Course objectives

  • Describe the architecture of a microcontroller
  • Write and debug embedded C programs
  • Use GPIO, timers, interrupts, ADC and PWM
  • Communicate with modules using UART, I2C and SPI
  • Combine these skills in a small embedded product

Prerequisites: Basic electronics. Basic programming knowledge is helpful but not essential.

Hours distribution

ComponentHours
Theory classes (8 units × 4 h)32
Practical sessions (14 labs × 4 h)56
Mini project8
Theory examination2
Practical examination4
Total102

32 hours

Theory syllabus

UnitTopicsHours
Unit 1Introduction to embedded systems
  • Embedded systems vs general-purpose computers
  • Applications in products and industry
  • Development workflow: write, compile, upload, test
4
Unit 2Microcontroller architecture
  • CPU, memory, registers and peripherals
  • Clock, reset and power
  • Pin configuration and datasheets
4
Unit 3Embedded C programming
  • Data types, operators and control structures
  • Functions, arrays and bit manipulation
  • Writing readable and reusable code
4
Unit 4GPIO, timers and interrupts
  • Digital input and output
  • Timers and delays
  • External and timer interrupts
4
Unit 5Analogue interfacing
  • ADC: reading analogue sensors
  • PWM: controlling brightness and speed
  • Signal scaling and calibration
4
Unit 6Serial communication
  • UART and serial monitor
  • I2C bus and devices
  • SPI bus and devices
4
Unit 7Displays and modules
  • Character LCD (16×2) with I2C
  • Keypads and switches
  • Real-time clock and EEPROM
4
Unit 8Embedded product development
  • From requirement to design
  • Testing, debugging and reliability
  • Documentation of an embedded product
4

64 hours

Practical sessions

LabPractical assignmentHours
1LED patterns using GPIO4
2Push buttons with debouncing4
3Timer-based blinking without delay4
4External interrupt counter4
5Read a potentiometer with ADC4
6LED brightness control with PWM4
7DC motor speed control with PWM4
8UART communication with a computer4
9Interface a 16×2 LCD using I2C4
10Read a sensor over I2C4
11Interface an SPI device4
12Keypad entry with LCD display4
13Real-time clock and timed event4
14Debugging a faulty embedded program4
MPMini project: Embedded digital controller: keypad set-point, sensor reading, LCD display and relay output.8
Total practical hours64

Hardware, tools & software

  • Microcontroller development boards
  • 16×2 LCD with I2C adapter, keypads, potentiometers
  • Sensors, motors and relay modules
  • Real-time clock and EEPROM modules
  • Laptop with programming and debugging software

Learning outcomes

  • Program microcontrollers in embedded C
  • Interface displays, sensors and communication modules
  • Use timers, interrupts, ADC and PWM correctly
  • Develop and document a small embedded product

Assessment & certificate

ExaminationDuration
Theory: concepts, components and principles from the 8 units2 h
Practical: build, wire, program, test, fault-find; mini project presentation4 h

A training completion certificate is issued subject to successful completion of the programme and assessment requirements.

📄 Download this syllabus: English PDF · हिंदी PDF

Register for this programme

Course fee ₹3,000 is paid only after your batch is confirmed. Prefer WhatsApp? Register on WhatsApp.

CallWhatsAppQuote